Can You Mount TV on Brick – Numerous people want to know if can you mount a TV on a brick wall? Unquestionably. But mounting a TV on brick does take more training, knowledge, and tools than installing one on drywall.
Here in this guide, we will show you how you can hang a TV on a brick wall so you can make the most of your wall space and elevate your entertainment.
Can You Mount TV on Brick?
One of the highest benefits of modern, slim TVs is that you can mount them on a wall. Unlike old, bulky TVs that are essential to an entire living room corner or an entertainment center, today’s televisions can hang like artwork.
But if you have brick walls in your home you might feel the wall-mounted TV ship has sailed. Luckily that’s not the case. We’ll go over the tools you’ll need and how you can drill into your brick wall to mount your TV strongly. If you want to know more about hanging a TV on Brick Wall then read this article carefully.
What are the Supplies you need for Mounting a TV on a Brick Wall?
Hanging a TV on a brick wall is well within the abilities of a DIYer; you’ll just need certain tools and supplies:
- TV wall bracket: Wall brackets come in a variety of sizes geared to the size of the TV they can support.
- Power drill: Any power drill can do the work, but a cordless drill with a hammer function is best. Don’t use a power driver, as they can effortlessly over-tighten screws.
- Masonry drill bits: Masonry bits are a complete must. They have chisel-like tips and wings intended to drill into heavy-duty concrete and brick surfaces. Always keep in mind that numerous fastener kits come with a masonry bit.
- Level: A TV bracket typically has enough play for post-installation tweaking, but a level supports you get as close as likely while installing.
- Permanent marker: There aren’t several marking tools that show up well on brick, but a permanent marker works very fine.
- Anchors or concrete screws: For hanging a TV in brick, both plastic wall anchors and concrete screws will defiantly work. For larger, heavier TVs (over 75 pounds), concrete screws are suggested, but for lighter TVs, plastic wall anchor screws installed properly are more than sufficient.
- Driver bit for your anchor or screws: For plastic anchor screws, a #2 Phillips driver bit that you can constrict into your drill driver is typically best. For concrete screws, a #3 Phillips or a socket set will do the trick.
- Washers: The slots and holes on the mounting hardware might be too large for a screw head, in which case correctly-sized washers will be essential.
- Tape measure: A tape measure is a requirement for precise bracket placement.
- Hammer or rubber mallet: A rubber mallet might be the finest for tapping anchors into the brick, but a hammer will work as well and might be more real-world.
Can You Mount TV on Brick?
You simply have to follow these steps for mounting a TV on a brick wall.
Step 1: Choose a location
- Now, before you drill any holes, you need to be sure to find a location close enough to an electrical outlet and cable jack. The fewer visible cables, the well-looking the installation.
Step 2: Find the installation height
- With the TV located facedown, attach the bracket to the TV according to the bracket manufacturer’s directions. If your bracket is a two-piece, simply attach both pieces to the back of the TV as if they were mounted on the wall.
- You need to measure from the bottom of the wall bracket to the lowest of the TV. You’ll add this measurement to the TV’s desired height to simply find the bracket mount placed on the wall.
- If this dimension is 6 inches, and you’d like the bottom of the TV to be 48 inches from the ground, measure 54 inches high.
- Simply remove the bracket from the TV. For two-piece brackets, after that remove just the wall bracket.
Step 3: Mark the drill holes
- Now, Hold the wall bracket against the wall so the bracket’s bottom is at the height determined in step 2. You can also use a level to ensure the bracket is located evenly. Then, use the permanent marker to specify on the brick the location of each screw hole.
- If the marks end up on mortar lines, simply adjust the bracket to avoid the mortar and make a new mark for the drill hole. Mortar is much easier than brick, and the anchor’s grip will ultimately deteriorate. Always drill into the brick, but not within a half-inch of its edges as it can blow.
- Always keep in mind that numerous brackets offer several screw holes to select from. The bracket’s instructions will explain how many and which you’ll want to use.
Step 4: Drill the holes
- You need to mark the drill bit at a length just a bit longer than the anchor or screw by wrapping a small piece of painter’s tape around the bit at that point. If you need a hammer drill, set it to the hammer setting. Else, set the drill to its high speed.
- Now, Placing the tip of the drill bit on one of the marks, squeeze the trigger gradually until the bit starts to dig into the brick.
- As the bit digs into the brick, simply increase the drill speed.
Step 5: Install plastic anchors
- Simply Use a hammer or rubber mallet to tap the plastic anchors into the newly drilled holes until they’re flush with the wall.
Step 6: Install the bracket
- Slide washers onto the screws if essential. Holding the wall bracket in place (making sure it’s right side up), thread the screws through the bracket and into the pierced holes by hand.
- Now, after attaching the driver bit to the drill or fitting the correctly sized socket on a ratchet, tighten one screw.
Step 7: Install the TV
- For two-piece brackets, simply install the TV brackets (already attached to the TV) on the wall bracket. Many also have to lock screws or tabs that hold the TV in place—refer to your bracket instructions and do not skip this step.
- Modern Simple House Design
- Simple Modern 2bhk House Plan
- Simple Modern 3BHK House Plan
- False Ceiling Design Ideas
We have shared everything about hanging a TV on Brick Wall in this article on “Can You Mount TV on Brick” if the info that we shared above helped you in any way then do share it with others.